Scotsman Flaker/nugget ice machine Error Codes
Applies to: Flaker/nugget machines. Compiled and paraphrased from Scotsman's own Prodigy Flaked and Nugget Ice Machines Service Manual (F0522 through F1522, N0422 through N1322, including Prodigy Plus D series), hosted at scotsman-ice.com, which prints the full display code table, the strike and retry logic behind codes 1 and 2, and the code recall procedure. Always confirm against the manual for your exact model. Table last updated Aug 13, 2026.
Not your model? Other Scotsman code tables: Prodigy series cubers.
Machine down now? 19 companies in this directory name Scotsman on their own site, with who has been phone-confirmed and who covers nights. Or find an ice machine technician by city.
How to read the codes
Prodigy flaker and nugget machines (F and N models) show a single character on a display under the front panel, plus AutoAlert lights: a blinking red Water light means no water sensed, and a yellow De-scale light means the cleaning timer has expired. Letters are statuses, not faults: F is freeze mode, b is bin full, C is clean cycle, L is board locked, O is off. To recall the last 10 stored codes, hold Off for 3 seconds, then press Clean repeatedly to step from newest to oldest; hold Clean and Off together for 3 seconds to clear the log; reset from any numbered code by pressing Off, then On. Important: these numbers mean different things than on Scotsman cube machines (code 1 is long freeze on cubers), so match the table to your machine type. Every code display machine also keeps a log: hold Off for 3 seconds, then press Clean repeatedly to step through the last 10 diagnostic codes from most recent to oldest. Hold Clean and Off together for 3 seconds to clear the log, and reset from any shutdown code by pressing Off then On.
The codes
| Code | Meaning | Likely causes | Operator-safe steps | Technician work |
|---|---|---|---|---|
| 1 flashing | No ice sensed: retrying | The photo eyes at the chute saw no ice fall for 10 minutes (the first 6 minutes after start are ignored); the machine waits 10 minutes and retries, up to three strikes | Watch whether ice flows down the chute on the retry; clean scale off the photo eyes | Refrigeration and auger drive diagnosis if no ice is actually being made |
| 1 steady | No ice sensed: shut down | Three consecutive no-ice strikes; the machine stops and must be manually reset | Press Off, then On to reset once; if it returns, stop and record it | Refrigeration system and auger motor diagnosis |
| 2 flashing / steady | Auger motor high load | The auger drive is drawing too many amps: gear reducer or auger bearing damage, or a restriction between reservoir and evaporator; the control retries after 4 minutes, then shuts down steady on repeat overload | Reset once (Off, then On); if it recurs, stop running the machine | Gear reducer, bearing, and auger inspection |
| 3 | No water in reservoir | Water supply off, exhausted filters, low level, or a dirty water sensor | Restore water, change overdue filters, and have the sensor probes wiped clean | Float valve and water sensor service |
| 4 | Refrigeration pressure too high or low | High or low pressure cutout opened: dirty condenser or filter, fan failure, water flow problems, or refrigerant charge faults; the switches auto-reset and the controller restarts | Clean the air filter and check for blocked airflow; note how often it recurs | Refrigerant-side diagnosis (EPA 608 required) |
| All 4 upper lights flashing | Unit remotely locked out | A leasing or subscription control has locked the machine | Contact the leasing company | Not a repair condition |
| F | Freeze mode: the machine is making ice | Normal operation. A flashing F means freeze mode is pending: the auger drive motor is starting up, and the compressor joins once the F goes steady. | Nothing to do, this is the running state. If F flashes for a long time without going steady, note it for the technician. | A machine stuck at flashing F points at the auger drive start circuit: motor, start components, or controller output. |
| b | Bin full, ice making paused | The photo eyes at the chute see a full bin, or the optional bin thermostat circuit is open. The manual's diagnosis for a false b: ice or scale on the photo eyes, eye holders out of position, bin stat capillary iced or the stat failed open, or a cold ambient at the bin. | Use ice down below the sensor level and the machine restarts on its own. If the bin is not actually full, wipe the photo eyes clean per the maintenance procedure. | Check photo eye position and continuity, and on bin-stat machines check the thermostat continuity with the capillary warm; replace a stat that will not close. |
| C | Clean cycle running | Someone pressed Clean: the auger motor runs, the De-scale light blinks, and after 20 minutes the compressor joins for the descale sequence. | Let the full descale and sanitize procedure finish, keep the reservoir fed with solution as the manual describes, or the De-scale light will stay on. | If C shows without a commanded cleaning, check the Clean button and controller. |
| E | Controller self test failed | The controller's power up self test did not pass; the Power light also blinks green for a self test failure. | Reset once: press Off, then On. If E returns, book service. | Check 12 volt supply from the transformer and replace the controller if the self test keeps failing. |
| L | Board locked, buttons ignored | The controller lock feature is on, usually set deliberately to stop unauthorized switching. | Unlock per the manual: hold the On button for 3 seconds, keep holding, then press and release Off twice. | Same procedure; if the lock will not release, the controller has an input fault. |
| O | Machine switched off at the controller | Someone pressed Off, or the machine finished its shutdown after Off was pressed mid cycle. | Press and release On; the machine goes through startup and resumes in about two minutes. | If O will not clear on the On button, check the button switch and controller input. |
| d | Test mode active | A technician started test mode (hold Off 3 seconds, release, then hold Clean 3 seconds). | If you find the machine showing d, a service visit left it in test mode: press Off then On to reset to normal operation. | Use test mode for component checks, then reset the control before leaving site. |
If this needs an ice machine technician
19 companies in this directory name Scotsman on their own site: that page shows who has been phone-confirmed, who publishes 24/7 cover, and what each puts in writing. Start there if the brand matters more than the city.
Two questions worth reading before you ring anyone: what to do first when a code appears and how to tell whether it is yours to fix.
Or browse ice machines service companies by state:
Indiana: Evansville · Fort Wayne · Indianapolis · South Bend
Kentucky: Bowling Green · Lexington · Louisville · Owensboro
Ohio: Akron · Canton · Cincinnati · Cleveland · Columbus · Dayton · Sandusky · Toledo · Upper Sandusky · Youngstown
Pennsylvania: Allentown · Altoona · Erie · Harrisburg · Lancaster · Pittsburgh · Scranton · Williamsport
West Virginia: Charleston · Martinsburg · Morgantown · Wheeling
Related: the PM checklist that prevents the most common codes outright, and the operator guides for symptom-first diagnosis.
Not sure this is the right make? The lookup by code shows every make that uses a given code, and flags the ones that mean different things depending on the machine in front of you.